1 It is important to identify the details of network sections and devices that will be affected or involved in a new design. This information is included in which section of the Network Design
Requirements Document?
#Project Scope
#model number of the router
#installed Cisco IOS feature set and version#amount of DRAM
#device make and model
#size of system flash memory
4 What are two practices a network technician should follow when installing a new interface card in a router? (Choose two.)
#Handle the interface card by the edges to avoid static discharge.
#Push the interface card into place until the edge connector is seated securely
5 The new serial interface card for the router arrives and the network technician reads that it is hotswappable. What does this mean?
#The card can be installed while the router is powered on if the router supports this technology.
6 Refer to the exhibit. A network administrator issues the command shown to gain knowledge about a poorly documented network. Which two pieces of information can the network administrator discover from the command output? (Choose two.)
#One connected device has router capability.
#Five Cisco devices with CDP enabled are directly connected to device C3750-24_MDF
7 Refer to the exhibit. Which of the three Cisco IOS images shown will load into RAM?
#The router selects an image depending on the boot system command in the configuration.
8 An administrator wants to download a new Cisco IOS software version to the local router. Which command performs this task?
#copy tftp flash
9 Refer to the exhibit. The top of the output shows the Cisco Feature Navigator regarding a Cisco IOS image that the administrator wants to install on a router. Below it is the output from the show version command for that router. Which statement is true regarding the capacity of the router to
run this Cisco IOS image?
#There is not enough DRAM and flash.
10 Which two items are objectives of a WLAN design site survey? (Choose two.)
#identify coverage areas
#determine primary AP locations
11 Refer to the exhibit. Which two actions improve the weaknesses of the topology shown, assuming that each access layer segment is in its own subnet? (Choose two.)
#Implement redundant links to each server by adding additional NICs.
#Implement a backup firewall with a link to a secondary ISP and implement a redundant link to the DMZ.
12 A company is beginning to analyze their new Cisco IOS upgrade requirements. What is one of the router components that a network administrator must consider when selecting a new Cisco IOS version?
#interfaces and modules to be supported
13 An employee at a company notices that the wireless signal strength indicator on his laptop fluctuates from good to low. The network administrator decides to do a site survey of that area.
Which three factors need to be included in the survey? (Choose three.)
#number of users in the area
#location of the AP
#location of walls and filing cabinets in the office
14 The new network design for AnyCompany must include support of voice and video traffic. Before upgrading, the network designer checks whether the existing devices can support the new
requirements. Which three items does the designer need to check? (Choose three.)
#size of DRAM and flash on each device
#routers that will support HWICs and VWICs
#modules supported on the loaded Cisco IOS
15 A new Cisco IOS version has been copied into flash from a TFTP server. When a reload is issued to upgrade the Cisco IOS, the router freezes part of the way through the loading process. What
could be the problem?
#There is enough flash but not enough RAM in the router.
16 Refer to the exhibit. A network designer has no documentation and is attempting to create a logical diagram of the network using the output from show commands. What can be determined
from the output shown?
#The designer cannot telnet to the attached switch.
17 A production router is reloaded and finishes with a Router> prompt. What three facts can be determined? (Choose three.)
#POST occurred normally.
#A full version of the Cisco IOS was located and loaded.
#A configuration file was not located in NVRAM or from a TFTP server.
18 During a site survey, the network designer noticed that people were accessing the company wireless network from the parking lot. What should be done to stop the wireless signal from
radiating out into the parking lot?
#change the type of antenna attached to the AP
19 A network design project includes a review of the existing network. What is the purpose of this phase of the project?
#To determine what existing network devices require upgrades to meet the new
20 Refer to the exhibit. Based upon the Cisco IOS file naming convention, what is represented by the value ipvoicek9 listed in the IOS filename?
#feature set
21 Refer to the exhibit. What two items can be determined from the output? (Choose two.)
#R2 is a Cisco 2600 device.
#The version of the IOS is 12.3.
22 During a wireless site survey, a consultant is determining the hours of peak usage and the estimated number of users in each location. The consultant is currently in what step of the site survey process?
#the identification of coverage areas
23 Refer to the exhibit. The network administrator is attempting to install a new version of the IOS on R2. Based on the exhibited output, what are two possible reasons that the transfer failed?(Choose two.)
#Connectivity between R2 and the TFTP server was not verified.
#The administrator did not verify that the TFTP server is running.
24 In which section of the Network Design Requirements document would a network consulting team detail names and IP addresses of important networking components and servers, provide network diagrams and topologies, and define strengths and weaknesses of the network?
#state of the network
0 Response to "CCNA 4 - Chapter 3"
Posting Komentar
Saran dan Masukan lebih diutamakan, tidak suka menerima cacian tapi suka menerima sumbangan